Kia Telluride: Seat belt restraint system / Seat belt - Driver's 3-point system with emergency locking retractor
Buckling your seat belt
|
To fasten the seat belt in your Kia Telluride, slowly pull the belt from the retractor and insert the metal latch plate (1) into the buckle (2). A distinct "click" confirms that the latch has engaged correctly.
Once the lap portion has been positioned snugly across your hips, the seat belt automatically adjusts to the proper length. During normal driving, the belt allows natural movement when you lean forward gradually. However, during sudden braking, sharp maneuvers, or a collision, the emergency locking retractor immediately locks the belt to help restrain the occupant.
WARNING
Place the lap portion of the seat belt as low as possible across your hips and keep it snug. Never allow the lap belt to ride over your abdomen, as this can significantly increase the risk of serious injury or death during a collision.
|
The arm closest to the seat belt buckle should remain over the belt, while the opposite arm should stay underneath it, as illustrated. Never route the shoulder belt beneath the arm nearest the door.
TIP
If the seat belt cannot be pulled from the retractor, pull it firmly once and then allow it to retract slightly. After that, it should extend smoothly.
Releasing the seat belt
|
|
Press the release button (1) on the buckle to unfasten the seat belt.
Once released, the seat belt should retract automatically into the retractor. If it does not retract properly, inspect the webbing to ensure it is not twisted or caught before trying again.
Adjusting the height of shoulder belt
The shoulder belt anchor can be adjusted to one of four different positions to improve both comfort and occupant protection while driving the Kia Telluride.
|
|
The shoulder belt should never rest against your neck. For proper protection, it should cross the center of your chest and lie midway over your shoulder near the door.
To adjust the shoulder belt anchor, move the height adjuster to the position that best fits your seating posture.
- To raise the shoulder belt anchor, pull the height adjuster upward.
- To lower it, press the height adjustment button (1) while sliding the adjuster downward.
Release the button and verify that the anchor has locked securely by attempting to move it. Correct seat belt positioning is essential for the restraint system to operate effectively.
Improperly positioned seat belts can result in serious injuries during an accident.
WARNING
Shoulder belt positioning
Always confirm that the shoulder belt height adjuster is securely locked in the selected position. Never position the shoulder belt across your face or neck, and never wear it under your arm. Incorrect routing of the belt greatly reduces its protective capability.
WARNING
Seat belt replacement
After any collision, replace the complete seat belt assembly, even if no visible damage is present. In addition, any seat belt that does not operate correctly should be replaced immediately.
When properly fastened, each seat belt locks into the buckle located at its corresponding seating position.
|
|
|
|
|
|
|
WARNING
Before fastening any rear seat belt, verify that the latch plate matches the correct buckle. Never force the left or right seat belt into the center buckle, as doing so will not properly secure the occupant during a collision.
Stowing the rear seat belt
When the rear seat belts are not being used, the buckles can be stored in the pocket located between the rear seat cushion and seatback to help keep the passenger area organized.
|
|
|
|
3rd row seat |
|
|
|
|
TIP
The illuminated rear seat belt buckles make it easier for passengers to locate and fasten their seat belts in low-light conditions. This feature is available on the outer second-row seating positions and remains illuminated until the corresponding seat belt is fastened.
|
|
-
Route the seat belt webbing through the rear seat belt guides. This helps prevent the belts from becoming trapped behind or underneath the seats when they are folded or adjusted.
Figure 3. 2nd row seat 
Figure 4. 3rd row seat 
-
After inserting the seat belt into its storage position, pull upward on the webbing to remove any excess slack and keep the belt neatly secured.
TIP
When pulling the seat belt out for use, draw the latch plate slowly through the seat belt guide to help prevent the guide from becoming detached from the interior trim.
Seat belt warning
The Kia Telluride seat belt warning system combines visual indicators and audible alerts to remind occupants to fasten their seat belts before and during driving...
Pretensioner seat belt
Your Kia Telluride is equipped with pretensioner seat belts for the driver, front passenger, and occupants in the second and third seating rows...
Other information:
Kia Telluride (LQ2, 2027-2026) Owner's Manual: Power window lock button
The driver can disable the rear passenger power window switches by pressing the power window lock button into the locked position. This feature helps prevent unintended operation of the rear windows while the Kia Telluride is being driven. When the power window lock button is activated: The driver's master power window controls remain capable of operating every passenger window.
Kia Telluride (LQ2, 2027-2026) Owner's Manual: LCD display messages
Door, hood, liftgate, or sunroof open The LCD display in your Kia Telluride provides a visual warning whenever a door, the hood, the liftgate, or the sunroof is not fully closed.